The following STL files were designed for the Shinobi Mk1 and available for download.
Landing Skids
Two sets of landing skids including 1mm as well as 2mm motor screw clearance to ensure that screw ends are not touching motor windings. Note that the model needs to be mirror flipped to accommodate both sides of motor mounts. The landing skids should be printed in PLA with a minimum of 60% infill.
GPS Tail Mount
The GPS tail mount was designed specifically for the Matek M8Q GPS module (dimensions: L20 x W20 x H10mm) but may fit other brands. It is recommended to heat shrink the GPS to secure it in place. The mount should be printed in TPU with a minimum of 60% infill.
Crossfire Antenna Standoff Mount
The mount is meant to hold the stock Crossfire Antenna encased in 3mm diameter antenna tubing in the proper vertical orientation for long-range reception. The mount doubles as a standoff with a height of 8mm. The mount should be printed in TPU with a minimum of 60% infill.
VTX Antenna Hoist
Not gonna lie. This is basically a rubber band. But measured to fit this frame. It serves to secure a rear, side mounted VTX antenna by looping it around one of the holes at the rear of the top plate. The glorified rubber band should be printed in TPU at 100% infill.
VTX Antenna Tail Guide
The guide helps to keep the VTX antenna oriented in a semi upright position at the tail for optimal signal reception. The guide mounts to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.
Mini Immortal T Antenna Tail Mount
The mount holds a Mini Immortal T antenna in place at the base of the tail clear from the carbon fiber of the bottom plate. The mount is secured to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.
XM Plus Antenna Guide
The guide serves to orient XM Plus diversity antennas at an optimal 90 degree angle at the tail. The diversity antennas are heat-shrinked to the leads to keep them in place. The guide mounts to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.
Shinobi Mk1 STL Files
Updated on February 15, 2022
The following STL files were designed for the Shinobi Mk1 and available for download.
Landing Skids
Two sets of landing skids including 1mm as well as 2mm motor screw clearance to ensure that screw ends are not touching motor windings. Note that the model needs to be mirror flipped to accommodate both sides of motor mounts. The landing skids should be printed in PLA with a minimum of 60% infill.
GPS Tail Mount
The GPS tail mount was designed specifically for the Matek M8Q GPS module (dimensions: L20 x W20 x H10mm) but may fit other brands. It is recommended to heat shrink the GPS to secure it in place. The mount should be printed in TPU with a minimum of 60% infill.
Crossfire Antenna Standoff Mount
The mount is meant to hold the stock Crossfire Antenna encased in 3mm diameter antenna tubing in the proper vertical orientation for long-range reception. The mount doubles as a standoff with a height of 8mm. The mount should be printed in TPU with a minimum of 60% infill.
VTX Antenna Hoist
Not gonna lie. This is basically a rubber band. But measured to fit this frame. It serves to secure a rear, side mounted VTX antenna by looping it around one of the holes at the rear of the top plate. The glorified rubber band should be printed in TPU at 100% infill.
VTX Antenna Tail Guide
The guide helps to keep the VTX antenna oriented in a semi upright position at the tail for optimal signal reception. The guide mounts to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.
Mini Immortal T Antenna Tail Mount
The mount holds a Mini Immortal T antenna in place at the base of the tail clear from the carbon fiber of the bottom plate. The mount is secured to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.
XM Plus Antenna Guide
The guide serves to orient XM Plus diversity antennas at an optimal 90 degree angle at the tail. The diversity antennas are heat-shrinked to the leads to keep them in place. The guide mounts to the rear two standoffs. It should be printed in TPU with a minimum of 60% infill.